To do a fisher paykel fridge filter light reset, replace the water filter first, then clear the indicator with the filter reset control on your panel, which on many models means pressing and holding the filter reset button for about three seconds until the light turns green. The exact button and the way it is held differ by model and by panel, so your owner’s manual has the final say. This guide explains what the light is telling you, the general order of steps, why a light can stay on after a reset and what is not worth worrying about.
What does the filter light on a Fisher Paykel fridge mean?
The light is a reminder, not a fault. It counts time or water use and tells you the water filter is due for a change. Our guide to replacing the Fisher Paykel refrigerator water filter says Fisher & Paykel recommends a new filter every six months or after roughly 200 gallons, whichever comes first, and that most models flag it with an indicator that turns yellow at five months and red at six. The light does not measure how clean the filter is. It is a timer, and it will come on whether or not the water has changed. That is why a reset alone, without a new filter, only hides the reminder.
The indicator is separate from the spanner symbol, which means a stored error code is present. Our glossary of Fisher Paykel refrigerator display symbols explains the difference, so check that you are looking at the filter light and not at a service symbol.
How do you reset the water filter light?
Follow the order below, and treat the control details as model-specific. First, replace the filter with the cartridge your model takes, using the steps in the filter guide: turn off the ice maker, twist the old filter out, fit the new one until it clicks, and run water through the dispenser to flush it. Second, find the filter reset control on your panel. On many models it is a button, and holding it for about three seconds turns the light from red to green. Third, turn the ice maker back on and discard the first batches of ice, as the filter guide advises.
Panels differ by model, and the exact steps differ too, so check the owner’s manual for your panel. If you do not have the manual, the model number on the label inside the fridge will let you find it. We do not publish a table of panels and buttons, because a guess about your panel could change a different setting.

Why won’t the filter light go off after resetting?
There are three usual reasons. The first is that the reset was not held long enough, or the wrong control was pressed. Try again, holding the control as the manual says. The second is that the panel has a lock on, so the touch controls are not responding, and the lock has to be released first. The third is that the filter is not seated correctly, or the filter is not the right one for the model, which can leave the light on or leak. Remove the filter, reinstall it until it clicks and try the reset again.
If none of that helps, switch the fridge off at the breaker for two minutes, restore power and try once more. Our page on how to reset a Fisher Paykel refrigerator explains what a power cycle does and does not clear. A light that keeps coming back after a new filter and a correct reset is worth mentioning to a technician with your model number.
Can you turn the filter light off without replacing the filter?
Technically on some models you can clear the indicator without a new filter, but it is not a good idea. The filter removes chlorine and other contaminants and its capacity runs out whether or not the light says so. Water that tastes off, a slow dispenser or smaller ice cubes are signs of an exhausted filter. If you do not use the dispenser, you still need the filter, because water sits in it. If you decide not to fit one, check your manual for a bypass option on your model rather than leaving an old filter in place.
What problems look like a filter issue but are not?
A weak dispenser flow is often blamed on the filter, but a kinked supply line, a closed shutoff valve or a frozen fill tube can cause it too. Our guide to a Fisher Paykel refrigerator water dispenser not working lists the checks in order. Water around the filter housing after you fit a new cartridge points to a cartridge that is not seated, and our guide to a fridge leaking water covers what to check. If ice production has dropped, our ice maker troubleshooting guide is the next stop.
When should you call a technician?
Call if the light stays on after a new filter and a correct reset, if the dispenser still runs slowly with a new filter, or if water leaks at the housing. A technician can check the supply, the valve and the control. Our Fisher Paykel refrigerator repair page explains how a visit works.